ConvaTec 413160 (38mm) SUR-FIT Natura Durahesive Skin Barrier (Flexible)

Features & Specification :

• • Ref # 413160

• • Size: 38mm (1½") flange

• • Color: White

• • Cut-to-fit SUR-FIT Natura® Durahesive® Flexible Skin Barrier with Flange and White Tape Collar

• • For the management of stoma output in people with an ostomy, including colostomy, ileostomy, and urostomy

• • Plastic coupling ring provides audible clicks to confirm a secure connection to the pouch for added peace of mind

• • Durahesive® skin barrier provides added protection from liquid output. It gently swells and hugs the stoma through its turtlenecking effect, helping protect the surrounding stoma sensitive skin

• • White fabric collar increases flexibility for a better body fit

• • Suitable for use while showering, bathing, and swimming

• • Durahesive® skin barrier also helps support extended wear

Preparation of Skin Barrier/Wafer
1. Measure your stoma using the measuring guide provided. Select a skin barrier with a flange (white ring) at least 1/2 inch larger than your stoma size. For flush or retracted stomas, convex skin barriers are recommended.
2. Trace the exact same stoma size onto the center white release paper on the back of the skin barrier.
3. Cut along the tracing with a curved scissor. "If using a pre-cut wafer, no cutting necessary." ConvaTec skin barriers are available in Stomahesive and Durahesive", solid and flexible (white or tan collars) with or without convexity.
4. A caulking material, such as Stomahesive Paste or an Eakin Cohesive Seal, can be applied to the back of the skin barrier to further fill gaps between the wafer and the stoma. Allow the paste to set for one minute prior to application to the skin. (Do not spread the paste.)

Application of Skin Barrier/Wafer
5. Center the skin barrier over the stoma. Press the skin barrier against the skin. If using a tape bordered skin barrier, remove the remaining backing paper one side at a time.
6. During application, maintain gentle pressure on the skin barrier for 30 seconds to improve adhesion

Attachment of Pouch
1. Before attaching the pouch, allow a small amount of air to enter the pouch by gently separating it.
2. If you are using a SUR-FIT Natura" drainable pouch with a clip, for attachment of the tail clip, fold the bottom of the pouch over the tail clip only once. Press firmly on the center of the clip until it snaps securely closed.
3. If you are using a SUR-FIT Natura urostomy drainable pouch with a tap, make sure the tap on the pouch is closed before attaching pouch to wafer.
4. If you are using the InvisiClose" tail closure system, a clip-less system, see the instructions for use provided in the pouch box.
Align the flange on the pouch with the flange on the skin barrier. Press them together beginning at the bottom and circling around the top side of the flange. You will hear several clicks as the system locks into place

Removal of Pouch
To easily remove the pouch from the skin barrier, gently pull downward on the plastic pouch tab and lift the pouch off. Anchor the wafer by holding it down with your other hand.
SUR-FIT Natura" closed-end pouches: Remove and discard as needed. (Do not flush.)
Filter covers are waterproof and should be used when bathing or swimming to prevent the filter from becoming wet. Remove filter cover after patting pouch dry.

Removal of Skin Barrier/Wafer
Gently pull the skin barrier down, away from the skin, while supporting the adjacent skin with your other hand. To assist with the barrier removal, an AllKare Adhesive Remover wipe may be used to remove any adhesive buildup.

Package Contents :

• 1N - ConvaTec 413160 (38mm) SUR-FIT Natura Durahesive® Flexible Skin Barrier